|
Bosa_nova
- 论坛博士后
- 19720110
- 911
- 914
- 2004-08-16
|
Bosa_nova论坛博士后
12#
t
T
发表于 2005-05-16 12:14
|只看楼主
有人光在嘴巴上指责AXX骗局是多么脏，却不肯贴实质性的东西给大家看，肯定是ABC的对手，故意出来搞混潭水的。 他不贴，我来贴！ 下面是JVC公司xrcd官方网站上的文字资料， 和网页链接，大家看一看就会很清楚了， 也可以挑挑毛病，ABC上的说明跟JVC的有无出入？ e x t e n d e d r e s o l u t i o n c o m p a c t d i s c f r o m J V C
The EXTENDED RESOLUTION COMPACT DISC (XRCD) from JVC brings the listener
higher fidelity and improved audio quality by enhancing the process of mastering and
manufacturing compact discs.
In most cases, after a record has been mastered, a U-matic 1630 format tape is
prepared and shipped to the manufacturing plant. At this point the artist, producer and
engineers can only hope that their work will return to them in a relatively unchanged
form. This manufacturing chain is not standardized, and while digitally correct, does not
always reproduce the highest audio quality possible. Since the manufacturing process
works as a number of components linked together in series, the overall performance can
only be limited by each stage. This means that extreme care and attention must be paid
to every aspect of mastering and manufacturing to get the most out of the process.
JVC has painstakingly gone through every step of the mastering and manufacturing
process with the goal of retaining the highest sonic purity of the original music.
This was accomplished not by just measuring the results, but in extensive listening tests
to determine the best configuration. Every combination of equipment, connections, AC
power regulation, word clock distribution, mastering format, delivery system and compact
disc construction was tested. The result is the XRCD, a compact disc that offers clearer
definition, more accurate imaging, and higher audio quality than any compact disc before.
The XRCD process starts at the mastering level. The analog signal is taken directly
from the mastering console and digitized using JVC’s 20 BIT K2 SUPER CODING.
The K2 is a 20 bit, 128 times over-sampling analog to digital converter which provides
a dynamic range of 108 dB, -96dB THD, flat frequency response in the passband to within+
0.05dB, and a substantial reduction of harmonic distortion for low level signals. The
K2 SUPER CODING also provides a bit down mode to convert 20 bits to 16 bits and
interface signal reshaping to eliminate time base jitter in the digital data stream. These
two functions are taken advantage of during manufacturing. The 20 bit digital signal is
then transferred to a Sony PCM-9000 using SDIF-2. The Sony PCM-9000 stores the information
on a magneto-optical disc instead of transferring it to the U-matic 1630 format
tape. The XRCD process takes advantage of the stability of the magneto-optical disc,
as well as its 20 bit capacity, and by using it as the audio storage medium for delivery
to manufacturing.
At the JVC manufacturing plant in Yokohama, the 20 bit Sony PCM-9000 magnetooptical
disc is is converted to 16 bits using the K2 SUPER CODING in bit down mode,
via a SDIF-2 connection. This stage resolves the high resolution 20 bit signal to 16 bits
while retaining the integrity of the low level information, which insures a true 16 bit
dynamic range without noise shaping. The 16 bit signal is then EFM encoded.
Another K2 circuit, called the K2 LASER, is used to regenerate the EFM signal
right before going to the laser of the glass cutter. This last stage is the same circuit used
for the K2 SUPER CODING interface, which eliminates any time based jitter that may
be present in the data stream. Throughout this process, the word clock is amplified and
distributed to the other stages to keep signal quality at a maximum. Similarly, all equipment
is run off regulated AC power feeds to provide a pure base from which to work. All
cables and connections between equipment use the SDIF-2 interface for sonic quality
and music integrity. Tests determined the SDIF-2 offered a superior transmission of
digital audio, far above the AES/EBU standard. A variety of materials, including 24k gold
and pure copper were tested, and ultimately aluminum was decided upon after
extensive listening tests. The end result of this manufacturing process is the highest
quality digital transfer from mastering to compact disc.
All of this attention to detail allows the listener to enjoy the music just as the artist,
produced and engineers originally intended it. Every nuance of the performance is
duplicated as it was recorded, with higher accuracy in both soud quality and imaging.
This is the EXTENDED RESOLUTION COMPACT DISC.
For more information on the XRCD please visit WWW.XRCD.COM. • info@xrcd.net
|
xrcd制作流程图   JVC公司xrcd官方网站：http://www.xrcd.net/Shopping/process.asp xrcd官方网站的文字说明：
These two functions are taken advantage of during manufacturing. The 20 bit digital signal is then transferred to a PCM-9000 using SDIF-2. The PCM-9000 stores the information on a magneto-optical disk instead of transferring it to the U-matic 1630 format tape. The xrcd process takes advantage of the stability of the magneto-optical disk, as well as its 20 bit capacity, by using it as the audio storage medium for delivery to manufacturing.
At the JVC manufacturing plant in Yokohama, the 20 bit PCM-9000 magneto-optical disk is converted to 16 bits using the K2 Super Coding in bit down mode, via a SDIF-2 connection. This stage resolves the high resolution 20 bit signal to 16 bits while retaining the integrity of the low level information, which insures a true 16 bit dynamic range without using noise shaping. The 16 bit signal is then EFM encoded.
Another K2 circuit, called the K2 Laser, is used to reshape the EFM signal right before going to the laser of the glass cutter. This last stage is the same circuit used for the K2 Super Coding interface, which eliminates any time based jitter that may be present in the data stream. Throughout this process, the word clock is amplified and distributed to the other stages to keep signal quality at a maximum. Similarly, all equipment is run off regulated AC power feeds to provide a pure base from which to work. All cables and connections between equipment use the SDIF-2 interface for sonic quality and music integrity. Tests determined the SDIF-2 offered a superior transmission of digital audio, far above the AES/EBU standard. A variety of materials, including 24K gold and pure copper were tested. Ultimately aluminum was decided upon after extensive listening tests. The end result of this manufacturing process is the highest quality digital transfer from mastering to compact disc.
All of this attention to detail allows the listener to enjoy the music just as the artists, producer, and engineers originally intended it. Every nuance of the performance is duplicated as it was recorded, with higher accuracy in both sound quality and imaging.
This is the Extended Resolution Compact Disc.
|
|
